Flagship Varnish Qt - (MW)

Pettit Flagship Varnish

As the sun’s rays can create havoc with a boat's finish, Pettit Flagship Varnish offers 6 times more UV inhibitors delivering unequaled protection against the sun's damaging rays. A unique blend of phenolic and alkyd resins combined with tung and linseed oils provide excellent performance as well as a warm, light amber hue. Pettit Flagship Varnish has an ultraviolet light filter along with a light stabilizer that effectively screens the damaging rays of the sun for longer-lasting life. Pettit Flagship Varnish enjoys the highest build and film depth per coat and serves as excellent abrasion resistance along with its high gloss finish.

Features:

• Traditional warm, amber hue with outstanding gloss retention
• Highest build and film depth per coat
• Highest level of U.V. protection
• Extremely durable finish
• Easy to apply

When applying to bare wood, a minimum of four (4) coats is required, and when applying over existing varnish, a minimum of two (2) coats is required. Pettit Flagship Varnish should be applied in a slightly heavier coat of up to 4 wet-mils. Coats should be allowed to dry overnight before sanding or recoating.

Specifications:

• Coverage: 450 sq. ft/gal.
• Method: Brush or Spray
• Number of Coats: Bare Wood: 4 minimum  |  Existing Varnish: 2 minimum
• VOC: 420 grams/liter
• Sizes Available: 1 US Quart, 1 US Gallon

Associated Products:

• Pettit Brush Thinner -For brushing and clean up 
• Pettit Spray Thinner -Spraying Application
• Pettit EZ-Wood Sealer- For surface preparation on bare wood

How to Apply Pettit Flagship Varnish

Pettit Flagship High Build Varnish may be applied by brush, conventional or airless spray. Thinning is not normally required although on warm days use Pettit 120 Brushing Thinner at 5-10% by volume to ease brushing and maintain good flow and leveling. When spraying, use Pettit 121 Spraying Thinner up to 20% by volume.

• Application Method: Brush or Spray
• Number of Coats: Bare Wood: 4 minimum | Existing Varnish: 2 minimum
• Application Temp: 45°F Minimum | 90°F Maximum
• Thinners: 120 Brushing Thinner | 121 Spraying Thinner
• Coverage: 450 sq. ft. /gal.

SURFACE PREPARATION AND APPLICATION:

Bare Wood

• Sand surface completely smooth with 180-320 grit production paper. Wipe surface to remove sanding residue with a tack rag or rag dampened with Pettit 120 Brushing Thinner.
• For new work on open grained wood such as mahogany, oak, ash, ect. The use of Pettit or Z-Spar Paste Wood Filler Stain is required to achieve a smooth finish. Let dry overnight.
• For new work on close grained woods such as pine, maple, spruce, ect. The use of Pettit or Z-Spar Paste Wood Filler Stain is not normally required.
• Apply a generous covering coat of Pettit 2018 Clear Sealer and let it dry overnight. Sand thoroughly with 220 grit sandpaper.
• On especially rough or porous wood, a second coat of 2018 Clear Sealer may be applied.
• If applied, sand the second coat as well and wipe the surface clean with a tack rag or rag dampened with Pettit 120 Brushing Thinner.
• Apply at least 4 coats of Z-Spar 1015 Flagship Varnish.
• Let each coat dry overnight, sand with 220 grit sandpaper, and clean off sanding residue with a tack rag before applying the next coat.
• Sand the next to last coat with 400 grit production paper and clean off sanding residue before applying the final coat.

Varnished Wood

In Good Condition

• Wipe old varnish with Pettit 120 Brushing Thinner to be sure all dirt, polish and/or grease has been removed.
• Thoroughly sand the existing varnish with 180-220 grit production paper and wipe clean.
• Apply at least 2 coats of Z-Spar 1015 Flagship Varnish. Let the first coat dry overnight, sand with 400 grit sandpaper, clean off sanding residue then apply the final coat.

In Poor Condition

• Remove all the old varnish with a paint and varnish remover, or by sanding.
• Bleach the wood if necessary to remove water stains.
• Proceed with the system for bare wood shown above.

Bare Teak (or other oily woods)

• Sand the wood smooth with 120 grit production paper to open up the grain. Wipe the surface thoroughly with Pettit 120 Brushing Thinner in order to remove as much oil as possible.
• Apply a generous coat of Pettit 2018 Clear Sealer.
• Allow to dry overnight, then lightly sand the surface with 220 grit sandpaper and wipe it with a rag dampened with Pettit 120 Brushing Thinner.
• Apply at least 4 coats of Z-Spar 1015 Flagship Varnish.
• Let each coat dry overnight, sand with 220 grit sandpaper, and clean off sanding residue with a tack rag before applying the next coat.
• Sand the next to last coat with 400 grit production paper and clean off sanding residue before applying the final coat.

APPLICATION:

• Do not shake varnish. Stir gently before application.

Information sourced from the Pettit Z-Spar Flagship Varnish Traditional Marine Varnish Technical Bulletin.

 Click Here to Download Pettit Flagship Varnish Application Instructions

Frequently Asked Questions

What is Pettit Flagship Varnish used for?

Pettit Flagship Varnish is a high-gloss marine varnish designed to provide a durable finish with a traditional warm, light amber hue. Its UV inhibitors, ultraviolet light filter, and light stabilizer help protect the finish from damaging sunlight while its high film build provides abrasion resistance and gloss retention.

How many coats of Pettit Flagship Varnish are needed on bare wood?

A minimum of four coats is required when applying Pettit Flagship Varnish to bare wood. Each coat should be allowed to dry overnight before sanding and recoating. The next-to-last coat should be sanded with 400-grit paper before the final coat is applied.

How many coats of Pettit Flagship Varnish are needed over existing varnish?

For existing varnish in good condition, apply a minimum of two coats. The existing surface should be cleaned and thoroughly sanded with 180-220 grit paper first. Allow the first new coat to dry overnight, then sand with 400-grit paper and remove the sanding residue before applying the final coat.

Can Pettit Flagship Varnish be used on teak and other oily woods?

Yes. For bare teak or other oily woods, sand the surface with 120-grit paper to open the grain and wipe it thoroughly with Pettit 120 Brushing Thinner to remove as much oil as possible. Apply Pettit 2018 Clear Sealer, allow it to dry overnight, then proceed with at least four coats of Flagship Varnish.

How can Pettit Flagship Varnish be applied?

Pettit Flagship Varnish can be applied by brush, conventional spray, or airless spray. Thinning is normally not required, but Pettit 120 Brushing Thinner can be used at 5-10% by volume for brushing in warm conditions. For spraying, Pettit 121 Spraying Thinner can be used up to 20% by volume. Stir gently before application and do not shake.

What are the application temperature and coverage specifications for Pettit Flagship Varnish?

Apply Pettit Flagship Varnish at temperatures between 45°F and 90°F. The stated coverage is 450 square feet per gallon. The product should be applied in a slightly heavier coat of up to 4 wet mils, with drying times varying according to temperature and conditions.

California Residents: WARNING Cancer and Reproductive Harm - P65Warnings.ca.gov