BoatLife Git Rot" - 16oz - (MW)

BoatLife Git Rot Penetrating Epoxy Kit

BoatLife Git Rot system is a superior product to combat dry rot because it works without having to remove dry rotted fibers. Unique two-part liquid Git Rot Epoxy saturates and restores original strength to wood by penetrating the rot. Wood must be dry for application. Apply by injecting "Git" Rot Epoxy into the wood. The epoxy will soak into wood by capillary action.

• Cures overnight
• Sandable and paintable, can be drilled and screwed
• Compatible with fiberglass resins, epoxies and most sealants
• Great for transoms, stringers and cabin roof rot in both fiberglass and wood boats

***WILL SHIP GROUND ONLY TO THE CONTIGUOUS 48 STATES ONLY***

How to Use BoatLife Git Rot Epoxy

For complete saturation and ultimate strength (in average type rot), it will require a volume of Git Rot approximately equal to half the volume of the rotted wood.

• Time and Temperature
• Optimum temperature for applying Git Rot Epoxy is between 50°F and 70°F.
• Only mix small batches (not more than 4 oz.) since the larger the quantity the greater the reaction and the faster the cure.
• After adding 1 part "B" to 3 parts "A", shake vigorously for at least 1 full minute. Once the two parts have been thoroughly mixed, a thermal reaction will begin to occur.
• Penetration is best immediately after mixing.
• Provide Reservoirs
• Where rot is deep into a large member, it is advisable to drill a staggered series of overlapping holes approximately 1/4" in diameter, 2" apart, slanting downwards. This will expose the necessary end grain and provide reservoirs for the penetration.
• In areas where sections of rot contain extensive holes where wood fibers are actually missing, it is recommended to mix sawdust with Git Rot Epoxy and use it as a fill material.
• In areas such as transoms, stringers, and balsa core decking, drilling thru the fiberglass surface may be necessary. For transom repairs, you may drill vertically down through the transom, and then pour in Git Rot.
• For decking, drill through the surface to treat the wood underneath. Holes left by drilling may be filled with a mixture of dry saw dust and Git Rot or a marine repair epoxy compound.
• Application
• The fastest and most efficient way to apply Git Rot epoxy is into the end grain of the wood.
• To avoid trapping air in the middle of the rot, always start at one end or on one surface and work progressively along.
• Continue until complete saturation is achieved. *This is determined when the reservoir holes fill and remain filled, and the surface remains shiny
• Properly applied, Git Rot solidifies into a tough resilient mass overnight. Allow one week for ultimate strength.

Click here to download BoatLIFE Git Rot application tips from the manufacturer.

Git Rot Epoxy will eventually cure into damp wood, however wet wood cannot be fully saturated or the product will lose its effectiveness. Be sure to dry the area as much as possible before application.

Frequently Asked Questions

What is BoatLife Git Rot Penetrating Epoxy Kit used for?

BoatLife Git Rot Penetrating Epoxy Kit is designed to penetrate and restore dry-rotted wood without requiring removal of the rotted fibers. It can be used for rot repairs in transoms, stringers, and cabin roofs on fiberglass and wood boats. The epoxy saturates the wood through capillary action and restores strength as it cures.

Does the wood need to be dry before applying BoatLife Git Rot Epoxy?

Yes. The wood should be dried as much as possible before application because wet wood cannot be fully saturated and can reduce the product's effectiveness. Although Git Rot Epoxy will eventually cure in damp wood, penetration is best when the wood is dry.

What is the mixing ratio for BoatLife Git Rot Epoxy?

Mix 1 part of component B with 3 parts of component A. Only mix small batches of no more than 4 ounces because larger quantities create a greater reaction and faster cure. Shake the two components vigorously for at least one full minute after combining them.

How do you apply BoatLife Git Rot Epoxy to rotted wood?

Apply Git Rot Epoxy into the end grain whenever possible, working progressively from one end or surface to avoid trapping air. For deep rot, approximately 1/4-inch holes spaced about 2 inches apart can provide reservoirs for penetration. Continue applying epoxy until the wood is saturated, indicated by filled reservoir holes and a shiny surface.

How much BoatLife Git Rot Epoxy is needed for rotted wood?

For complete saturation and ultimate strength in average-type rot, the volume of Git Rot Epoxy required is approximately half the volume of the rotted wood. Extensive areas where wood fibers are missing can be filled using a mixture of sawdust and Git Rot Epoxy.

How long does BoatLife Git Rot Epoxy take to cure?

Properly applied Git Rot Epoxy solidifies into a tough, resilient mass overnight and can be sanded, painted, drilled, and screwed after curing. Allow approximately one week for ultimate strength. The optimum application temperature is between 50°F and 70°F, and penetration is best immediately after mixing.

California Residents: WARNING Cancer and Reproductive Harm - P65Warnings.ca.gov